[2017 New Update] Up To Date Cisco 300-101 Dumps PDF Exam Youtube Study Guide With Low Price Implementing Cisco IP Routing

What is the best way to prepare for Cisco certification exam 300-101 dumps? The Implementing Cisco IP Routing (300-101 ROUTE) exam is a 120 minutes (45-65 questions) assessment in pass4itsure that is associated with the CCNP Routing and Switching CCDP certification.”Implementing Cisco IP Routing” is the exam name of Pass4itsure Cisco 300-101 dumps test which designed to help candidates prepare for and pass the Cisco 300-101 exam.Up to date Cisco 300-101 dumps pdf exam Youtube study guide with low price Implementing Cisco IP Routing. To make sure an outstanding performance at the certification exam and thus be able to get in having the Cisco https://www.pass4itsure.com/300-101.html dumps certification with a top position, you should take care of an appropriate form of Cisco 300-101 training.

[2017 New Cisco 300-101 Dumps Update From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWWDdYaFM0SVFwMTA

[2017 New Cisco 200-355 Dumps Update From Google Drive]: https://drive.google.com/open?id=0BwxjZr-ZDwwWUkUwT0lYclNxbFU

300-101 dumps

Pass4itsure Latest and Most Accurate Cisco 300-101 Dumps Exam Q&As:

QUESTION 1
Refer to the exhibit.
300-101 dumps

Which one statement is true?
A. Traffic from the 172.16.0.0/16 network will be blocked by the ACL.
B. The 10.0.0.0/8 network will not be advertised by Router B because the network statement for the 10.0.0.0/8 network is missing from Router B.
C. The 10.0.0.0/8 network will not be in the routing table on Router B.
D. Users on the 10.0.0.0/8 network can successfully ping users on the 192.168.5.0/24 network, but users on the 192.168.5.0/24 cannot successfully ping users on
the 10.0.0.0/8 network.
E. Router B will not advertise the 10.0.0.0/8 network because it is blocked by the ACL.
300-101 exam 
Correct Answer: E
Explanation
Explanation/Reference:
Explanation:
You can filter what individual routes are sent (out) or received (in) to any interface within your EIGRP configuration.
One example is noted above. If you filter outbound, the next neighbor(s) will not know about anything except the 172.16.0.0/16 route and therefore won’t send it to anyone else downstream. If you filter inbound, YOU won’t know about the route and therefore won’t send it to anyone else downstream.
QUESTION 2
A router with an interface that is configured with ipv6 address autoconfig also has a link-local address assigned. Which message is required to obtain a global unicast address when a router is present?
A. DHCPv6 request
B. router-advertisement
C. neighbor-solicitation
D. redirect
Correct Answer: B
Explanation
Explanation/Reference:
Explanation:
Autoconfiguration is performed on multicast-enabled links only and begins when a multicast- enabled interface is enabled (during system startup or manually). Nodes (both, hosts and routers) begin the process by generating a link-local address for the interface. It is formed by appending the interface identifier to well known link-local prefix FE80 :: 0. The interface identifier replaces the right-most zeroes of the link-local prefix. Before the link-local address can be assigned to the interface, the node performs the Duplicate Address Detection mechanism to see if any other node is using the same link-local address on the link. It does this by sending a Neighbor Solicitation message with target address as the “tentative” address and destination address as the solicited-node multicast address corresponding to this tentative address. If a node responds with a Neighbor Advertisement message with tentative address as the target address, the address is a duplicate address and must not be used. Hence, manual configuration is required. Once the node verifies that its tentative address is unique on the link, it assigns that link-local address to the interface. At this stage, it has IP-connectivity to other neighbors on this link. The autoconfiguration on the routers stop at this stage, further tasks are performed only by the hosts. The routers will need manual configuration (or stateful configuration) to receive site-local or global addresses. The next phase involves obtaining Router Advertisements from routers if any routers are present on the link. If no routers are present, a stateful configuration is required. If routers are present, the Router Advertisements notify what sort of configurations the hosts need to do and the hosts receive a global unicast IPv6 address.
QUESTION 3
An engineer has configured a router to use EUI-64, and was asked to document the IPv6 address of the router. The router has the following interface parameters: mac address C601.420F.0007 subnet 2001:DB8:0:1::/64 Which IPv6 addresses should the engineer add to the documentation?
A. 2001:DB8:0:1:C601:42FF:FE0F:7
B. 2001:DB8:0:1:FFFF:C601:420F:7
C. 2001:DB8:0:1:FE80:C601:420F:7
D. 2001:DB8:0:1:C601:42FE:800F:7
300-101 dumps 
Correct Answer: A
Explanation
Explanation/Reference:
Explanation:
Extended Unique Identifier (EUI), as per RFC2373, allows a host to assign iteslf a unique 64-Bit IP Version 6 interface identifier (EUI-64). This feature is a key 
benefit over IPv4 as it eliminates the need of manual configuration or DHCP as in the world of IPv4. The IPv6 EUI-64 format address is obtained through the 48-bit MAC address. The Mac address is first separated into two 24-bits, with one being OUI (Organizationally Unique Identifier) and the other being NIC specific. The
16-bit 0xFFFE is then inserted between these two 24-bits to for the 64-bit EUI address. IEEE has chosen FFFE as a reserved value which can only appear in EUI- 64 generated from the EUI-48 MAC address. Here is an example showing how the Mac Address is used to generate EUI.

300-101 dumps

Next, the seventh bit from the left, or the universal/local (U/L) bit, needs to be inverted. This bit identifies whether this interface identifier is universally or locally administered. If 0, the address is locally administered and if 1, the address is globally unique. It is worth noticing that in the OUI portion, the globally unique addresses assigned by the IEEE has always been set to 0 whereas the locally created addresses has 1 configured. Therefore, when the bit is inverted, it maintains its original scope (global unique address is still global unique and vice versa). The reason for inverting can be found in RFC4291 section 2.5.1.
QUESTION 4
For security purposes, an IPv6 traffic filter was configured under various interfaces on the local router. However, shortly after implementing the traffic filter, OSPFv3 neighbor adjacencies were lost. What caused this issue?
A. The traffic filter is blocking all ICMPv6 traffic.
B. The global anycast address must be added to the traffic filter to allow OSPFv3 to work properly.
C. The link-local addresses that were used by OSPFv3 were explicitly denied, which caused the neighbor relationships to fail.
D. IPv6 traffic filtering can be implemented only on SVIs.
Correct Answer: C
Explanation
Explanation/Reference:
Explanation:
OSPFv3 uses link-local IPv6 addresses for neighbor discovery and other features, so if any IPv6 traffic filters are implemented be sure to include the link local address so that it is permitted in the filter list.
QUESTION 5
What is the purpose of the autonomous-system {autonomous-system-number} command?
A. It sets the EIGRP autonomous system number in a VRF.
B. It sets the BGP autonomous system number in a VRF.
C. It sets the global EIGRP autonomous system number.
D. It sets the global BGP autonomous system number.
300-101 pdf 
Correct Answer: A
Explanation
Explanation/Reference:
Explanation:
To configure the autonomous-system number for an Enhanced Interior Gateway Routing Protocol (EIGRP) routing process to run within a VPN routing and forwarding (VRF) instance, use the autonomous-system command in address-family configuration mode. To remove the autonomous-system for an EIGRP routing process from within a VPN VRF instance, use the no form of this command. autonomous-system autonomous-system-number no autonomous-system autonomous-system-number
Reference:
QUESTION 6
Which type of traffic does DHCP snooping drop?
A. discover messages
B. DHCP messages where the source MAC and client MAC do not match
C. traffic from a trusted DHCP server to client
D. DHCP messages where the destination MAC and client MAC do not match
Correct Answer: B
Explanation
Explanation/Reference:
Explanation:
The switch validates DHCP packets received on the untrusted interfaces of VLANs with DHCP snooping enabled. The switch forwards the DHCP packet unless any of the following conditions occur (in which case the packet is dropped): The switch receives a packet (such as a DHCPOFFER, DHCPACK, DHCPNAK, or DHCPLEASEQUERY packet) from a DHCP server outside the network or firewall. The switch receives a packet on an untrusted interface, and the source MAC address and the DHCP client hardware address do not match. This check is performed only if the DHCP snooping MAC address verification option is turned on. · The switch receives a DHCPRELEASE or DHCPDECLINE message from an untrusted host with an entry in the DHCP snooping binding table, and the interface information in the binding table does not match the interface on which the message was received. The switch receives a DHCP packet that includes a relay agent IP address that is not 0.0.0.0. To support trusted edge switches that are connected to untrusted aggregation-switch ports, you can enable the DHCP option-82 on untrusted port feature, which enables untrusted aggregation- switch ports to accept DHCP packets that include option-82 information. Configure the port on the edge switch that connects to the aggregation switch as a trusted port.

QUESTION 7
Which statement is true about the PPP Session Phase of PPPoE?
A. PPP options are negotiated and authentication is not performed. Once the link setup is completed, PPPoE functions as a Layer 3 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.
B. PPP options are not negotiated and authentication is performed. Once the link setup is completed, PPPoE functions as a Layer 4 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.
C. PPP options are automatically enabled and authorization is performed. Once the link setup is completed, PPPoE functions as a Layer 2 encapsulation method that allows data to be encrypted over the PPP link within PPPoE headers.
D. PPP options are negotiated and authentication is performed. Once the link setup is completed, PPPoE functions as a Layer 2 encapsulation method that allows data to be transferred over the PPP link within PPPoE headers.
300-101 vce 
Correct Answer: D
Explanation
Explanation/Reference:
Explanation:
PPPoE is composed of two main phases:
Active Discovery Phase–In this phase, the PPPoE client locates a PPPoE server, called an access concentrator. During this phase, a Session ID is assigned and the PPPoE layer is established. PPP Session Phase–In this phase, PPP options are negotiated and authentication is performed. Once the link setup is completed, PPPoE functions as a Layer 2 encapsulation method, allowing data to be transferred over the PPP link within PPPoE headers

300-101 dumps

With training and an outstanding level of experience, you will be able to get the 300-101 dumps in less time and with less effort, and you will also find the particular abilities and information needed in your upcoming career as an IT professional particular in Cisco 300-101 technology and products. We are devoted to the process of resource and third celebration mortgage approvals. We believe Cisco https://www.pass4itsure.com/300-101.html dumps masters and professionals as well have an entitlement to the guarantee of quality protection of these study materials and content.

Cisco 300-101 Dumps Youtube:https://youtu.be/Kzd25sHJz1A

Comments are closed